Im looking to redo my fuel lines.
I have a tunnel ram with duel holley carbs. So I need to split 1 fuel line to 4 places. Any ideas on where to find parts. I want to do it all in ss braided line.
Printable View
Im looking to redo my fuel lines.
I have a tunnel ram with duel holley carbs. So I need to split 1 fuel line to 4 places. Any ideas on where to find parts. I want to do it all in ss braided line.
Couldnt you get or make a fuel log?
Couldnt you get or make a fuel log?
Yeah. But 1 carb feeds on one side and the other carb feeds on the other side of the intake manifold.
superdave 013 here on the boards has everything you need to plumb up your system
sweet performance products
placentia calif
dave will hook you up right and is real fair with his pricing. you cant beat it.
Another vote for Superdave. His prices are good. Be careful though, its easy to get out of hand. :D
I use TMR in Orange, ca. I spent $800 in lines and fittings to plumb my tunnelram and fuel system properly, just be aware. Some of those fittings are 50 bucks a pop....
Also, do not try to save a few bucks by getting the non teflon lines - if you dry out the hoses, IE, you don't run your boat for a season or two, you will start having all kinds of leaks in the mdlle of the hose. I found that out the hard way.
The teflon lined stuff never wears out.
I have a similiar setup for my blower motor its a #8an on each side then a Y into 2 #6an here is a pic;)
http://www.***boat.com/forums/attach...1&d=1187399566
Pick up a 4 port fuel pressure regulator and take everything to SuperDave. Piece of cake.
Here is the best pic of my setup.
http://www.***boat.com/image_center/.../20TRbling.jpg
Here is the best pic of my setup.
http://www.***boat.com/image_center/.../20TRbling.jpg
This would work for me. but my carbs are going the other way.
Here is the best pic of my setup.
http://www.***boat.com/image_center/.../20TRbling.jpg
hmmm; looks familiar...
superdave is great, but since you're in havasu, you also might want to check out pure choice in the 2100 block of west acoma. seems like all he does is make up lines. i haven't used 'em, don't know anything about pricing, etc., but i did pick up a couple last minute items from him before going to texas, and a couple people recommended him to me. i plan on using him for a couple small things i want to do... nice to have a local guy.
hmmm; looks familiar...
superdave is great, but since you're in havasu, you also might want to check out pure choice in the 2100 block of west acoma. seems like all he does is make up lines. i haven't used 'em, don't know anything about pricing, etc., but i did pick up a couple last minute items from him before going to texas, and a couple people recommended him to me. i plan on using him for a couple small things i want to do... nice to have a local guy.
Ok, I have a question...that intake manifold has 2 waterports next to the one in the middle...why not do a block off plate and use those ports, rather than plugging them?
hmmm; looks familiar...
superdave is great, but since you're in havasu, you also might want to check out pure choice in the 2100 block of west acoma. seems like all he does is make up lines. i haven't used 'em, don't know anything about pricing, etc., but i did pick up a couple last minute items from him before going to texas, and a couple people recommended him to me. i plan on using him for a couple small things i want to do... nice to have a local guy.
yes they do make up hoses. Gary is the man to talk to over there.
Thanks for the good words everyone.