How well does powder coating on a jet hold up? I heard that that its no good to strip the hardened surface on the aluminum eek! when they sand blast before powder coat? Whats that about? What about Jet-Hot( Jet hot site )? Got some pics? Anthony
Printable View
How well does powder coating on a jet hold up? I heard that that its no good to strip the hardened surface on the aluminum eek! when they sand blast before powder coat? Whats that about? What about Jet-Hot( Jet hot site )? Got some pics? Anthony
Ranz1:
How well does powder coating on a jet hold up? I heard that that its no good to strip the hardened surface on the aluminum eek! when they sand blast before powder coat? Whats that about? What about Jet-Hot( Jet hot site )? Got some pics? Anthony well when i did my bowl (powder caoted) i used a paint striper so i didnt remove the hard anadizing undre the many layer s of paint. then i snaded it smooth and pre cooked it for like a hour and a half to get all the gas bubbles and oil or what ever mighht be in the metal and i wen a head and pc 'ed it . here are some pics of mine.
[img]http://www.***boat.com/image_center/data/500/36DSCN1893-med.JPG[/img]
[img]http://www.***boat.com/image_center/data/500/36DSCN1898-med.JPG[/img]
and some other stuff i have done
[img]http://www.***boat.com/image_center/data/500/36Dscn1826.jpg[/img]
every thing on my pump is powder coated and my rail kit (except for the rails) and gas caps and other stuff i love powder coating all my stuff . i do it my self so i save a ton on it. it lasts very well on pumps if done right! wink
Nice job Tyson!
LVjetboy:
Nice job Tyson! thanks ! wink
Tyson what color is that blue it kinda looks tranparent did you have to put a silver base under neath it?Looks nice can you post a pic of the rail kit since it is a Ford making my own and would like to see as maney as posible for ideas and alt location.
Thanks Jake :D
i had my bowl, diverter nozzle, rail kit and other hardware done and its held up great. [img]http://www.***boat.com/image_center/data/500/45IMG_0266-med.JPG[/img]
Jake W:
Tyson what color is that blue it kinda looks tranparent did you have to put a silver base under neath it?Looks nice can you post a pic of the rail kit since it is a Ford making my own and would like to see as maney as posible for ideas and alt location.
Thanks Jake :D jake i will see is i can find any other pics of it . if not ill take some. as for the blue it is transparent and should be used on polished or cromwed parts ( i have used a powder undernieth it called almost crome and it turns out pretty damn good, my motor plates are done up that way)
[img]http://www.***boat.com/image_center/data/520/36DSCN2092-med.JPG[/img]
[img]http://www.***boat.com/image_center/data/520/36DSCN2098-med.JPG[/img]
[img]http://www.***boat.com/image_center/data/520/36DSCN2080-med.JPG[/img]
[ September 28, 2003, 06:31 PM: Message edited by: hack job ]
Tyson very clean thanks for the pics. jawdrop
Jake :D
I swear this thread was up about a week ago. Anyway i say paint it. heres mine...I used polyeurethane paint for it,its color matched to a new place diverter so i could add one without any painting hassles. Good luck.
[img]http://www.***boat.com/image_center/data/521/409Dcp00468-med.jpg[/img]
[img]http://www.***boat.com/image_center/data/521/409Dcp00470-med.jpg[/img]
painting looks just like powdercoat but a turdload cheaper and besides, whoever has their pump powdercoated needs to inform the knucklehead behind the counter that the tape covering all of the areas with holes or clearences needs to do w/out powdercoating!! i know of a few peops that have had this happen to them incl. me!!! removing powdercoating from threading is a "BIATCH" just my "BUCK-O-FIVE"