-
I am searching for Nicson marine hardware to install a Chrysler Imperial 392 HEMI engine.
Nicson rear engine mount (aquired used, eBay)
Rear engine mid plate (aquired used, from Chuck Taylor's HEMI store)
Nicson front engine mount
Nicson exhaust logs and elbows (aquired from Bobbo541 with risers)
Exhaust elbows donated by Sanger Pete (thanks a bunch!)
http://www.hemiengineparts.com/index.html (http://)
http://www.hotboatpics.com/pics/data...alleyCover.jpg
http://www.hotboatpics.com/pics/data...263Sanger1.jpg
-
There is a set of mounts on ebay about every 2 weeks or so...
Almost always nicson... now the logs are alittle rarer... and the risers.... I've been looking for almost 18 months to find a pair of nicson risers for my pontiac ( same size as the hemis) you can also check boat wrecking yards its amazig what you can find....
-
I was watching some hemi boat stuff on ebay. Both of these sold within the last week or so.
Stuff seems to be out there.
http://cgi.ebay.com/ebaymotors/V-DRI...1285QQitemZ459 7664954QQrdZ1
http://cgi.ebay.com/ebaymotors/Edelb...QQitemZ4595872 957QQrdZ1
http://cgi.ebay.com/ebaymotors/Hemi-...202QQitemZ4594 638928QQrdZ1QQsspagenameZWDVW
-
there's a boat yard in Rancho Cordova that has all kinds of stuff. I can't recall the name of it but email Oldsquirt, I'm sure he'll know. That is if you don't know about it already.
-
I was watching some hemi boat stuff on ebay. Both of these sold within the last week or so.
Stuff seems to be out there.
http://cgi.ebay.com/ebaymotors/V-DRI...1285QQitemZ459 7664954QQrdZ1
http://cgi.ebay.com/ebaymotors/Edelb...QQitemZ4595872 957QQrdZ1
I watched those auctions. I was not familiar with the Cal Marine stuff and the Edelbrocks did not have the risers (snails).
I did manage to pick up some Nicson front and rear engine mounts, the rear engine mount was the piece that I was hoping was in usable condition for its age, but the holes for one of the stringer mounting adjuster plates were hacked up. Both stringer adjusting plates are Nicson, but they appear to be for a different year engine mount. The webs were ground down to clear some of the protruding features of the engine mount. The coupler was the only part that was not damaged by improper home machining. I wil have to see if I can repair the rear engine mount. The front engine mount was listed as being altered and would not fit into a restoration project. If I can't fix the front engine mount I will have to look for another one. I will have to be more careful of items offered on eBay.
http://cgi.ebay.com/ebaymotors/ws/eB...3ARTQ%3AUS%3A1
-
there's a boat yard in Rancho Cordova that has all kinds of stuff. I can't recall the name of it but email Oldsquirt, I'm sure he'll know. That is if you don't know about it already.
The boat salvage yard is called shipwreck.
-
A friend of mine has everything you need, I'll give him a call if you like. We are in Yuba City, home of Kung Fu BBQ sauce...C'mon! :D
-
There is a set of mounts on ebay about every 2 weeks or so...
Almost always nicson... now the logs are alittle rarer... and the risers.... I've been looking for almost 18 months to find a pair of nicson risers for my pontiac ( same size as the hemis) you can also check boat wrecking yards its amazig what you can find....
I found a set of Nicson exhaust manifolds at Chuck Taylor's without risers. Glenwood Marine has some risers that are made for the Chrysler wedge engine exhaust manifold they carry, They said that I might be able to adapt that riser model to the Nicson's. The flange is 4-7/8" diameter with a 3" exhaust outlet. The flanges are undrilled so that you can custom set them.
http://www.glenwoodmarine.net/Catalog/MANIFOLDS.pdf
-
A friend of mine has everything you need, I'll give him a call if you like. We are in Yuba City, home of Kung Fu BBQ sauce...C'mon! :D
That would be great. I would like to know what he has.
-
The boat salvage yard is called shipwreck.
Shipwreck Marine
2540 Grennan Court, Space 'C'
Rancho Cordova, CA 95742
(916) 635-1945
Thanks a bunch guys! I will give them a try.
-
There is also Rancho Marine Recycling (http://www.boatrecycling.com/)
-
There is also Rancho marine recycling not to far from them on sunrise ... http://www.boatrecycling.com/ they have alot of stuff...
3761 Unit C Recycle Rd. Rancho Cordova, CA 95742
Phone: (916) 638-8908
just head south on sunrise... make a right at the light after pic-n-pull thne go south they are at the end of the street.
-
"Napabob", talked to my friend about the Hemi stuff. Zoomies for sure, going to check on the other stuff!
-
Hud,
I have through transom exhaust holes. I am going to use a set of Nicson exhaust manifolds. I will be looking for some Nicson (hard to find) risers or try out a set of exhaust elbows.
-
YeLLowBoaT / OLDSQUIRT
I will be calling that recycling service also.
-
Get in touch with Nice Pair here on the boards. I think he has alot of Hemi hardware still.
-
Boatmaster,
I will send him a PM after the Christmas and New Year holidays.
Thanks a bunch!
-
Get in touch with Nice Pair here on the boards. I think he has alot of Hemi hardware still.
Boatmaster,
I have sent Nice Pair a PM.
Thanks for the lead.
-
those recycling places aren't far from me. so, if you need any help, let me know.
-
those recycling places aren't far from me. so, if you need any help, let me know.
NCG,
I need to give the recyclers a call, I am still looking for a set of Nicson exhaust risers (hard to find items) for a set of exhaust logs that I picked up from Chuck Taylor out of Cottonwood, CA.
-
I am looking for a 172 tooth ring gear aluminum flywheel
-
this one just ended today. I thought i saw where you were watching it?
http://cgi.ebay.com/ebaymotors/Early...2QQitemZ460388 6939QQrdZ1
-
this one just ended today. I thought i saw where you were watching it?
http://cgi.ebay.com/ebaymotors/Early...2QQitemZ460388 6939QQrdZ1
old rigger,
I was first bid on it until I was shot down by a sniper bidder on the last seconds. I have been talking to Tom Manier of JBP to see if he can locate another one.
Bob
-
old rigger,
I was first bid on it until I was shot down by a sniper bidder on the last seconds.
Bob
Well that sucks. damn snipes.
I've had that happen a few times to me too.
-
napabob i have what your looking for nicson manifolds and risers for through the transon exhaust.call me 925 786 0214.
-
-
-
Shipwreck Marine
2540 Grennan Court, Space 'C'
Rancho Cordova, CA 95742
(916) 635-1945
Thanks a bunch guys! I will give them a try.
I called Shipwreck Marine and they do not carry items for a 392 HEMI.
-
napabob i have what your looking for nicson manifolds and risers for through the transon exhaust.call me 925 786 0214.
Your items will be in my budget for this month.
-
Napabob Iam sorry about the pics my sister took them but i havent seen them yet i will call her now.
-
http://cgi.ebay.com/ebaymotors/Nicso...55QQitemZ46086 99374QQrdZ1QQsspagenameZWDVW
http://i13.ebayimg.com/01/i/06/16/3c/b6_1.JPG
needs some polish but looks to be in good shape.
Then again these might look bad ass on your motor.... HERE (http://cgi.ebay.com/ebaymotors/Hilbo...Z33554QQitemZ8 034344995QQrdZ1)
-
YeLLowBoaT,
I was first bid on it, eBay had it removed due to discrepancies on the post. The message below is to me from eBay.
"Our records show that you bid on this listing. We have removed the listing from eBay because it violated eBay policy. You are not required to complete the transaction. The seller is free to relist the item in accordance with eBay's online policies. If the seller relists the item, you are free to bid on that item."
I am going for the HEMI Hot Heads raised aluminum intake manifold for a single marine carburetor.
-
Napabob Iam sorry about the pics my sister took them but i havent seen them yet i will call her now.
B541,
No rush, I just want to add them to my budget for February.
-
napabob i have what your looking for nicson manifolds and risers for through the transon exhaust.call me 925 786 0214.
Bob,
Thank you (and your dad) for helping me out in obtaining the exhaust system that I was looking for (a polished set).
http://www.hotboatpics.com/pics/data...tManifold2.jpg
-
-
http://www.***boat.com/image_center/...sale_F_N_R.jpg
I need opinions on the Casale shown above. The U. S. patent number puts it with a 1964 inventor publication.
Parts and service are still available. I have requested images for all six.
Ease of operation
Current value
Pros (Latin for 'for')
Cons (Latin for 'against')
The link to the patent is below. QuickTime Player is needed to view and ActiveX control needs to run.
http://patimg1.uspto.gov/.piw?Docid=...%2Fnetacgi%2Fn ph-Parser%3FSect1%3DPTO1%2526Sect2%3DHITOFF%2526d%3DP ALL%2526p%3D1%2526u%3D%2Fnetahtml%2Fsrchnum.htm%25 26r%3D1%2526f%3DG%2526l%3D50%2526s1%3D3154047.WKU. %2526OS%3DPN%2F3154047%2526RS%3DPN%2F3154047&PageN um=&Rtype=&SectionNum=&idkey=3000716FE330
-
Napa Bob glad to see those will be put to good use.
-
Napa Bob glad to see those will be put to good use.
I need to see some images of an installed one.
The guy that is selling it is out of England and he is saying that it is new and has never been installed.
Bob
-
Looking for a two fin skeg to replace the one shown below
4 3/8" x 18 1/4" (plus or minus 1/8")
http://www.hotboatpics.com/pics/data...Craft_skag.jpg