I get mine at Grainger. I believe I paid $7.00 per spray can (slip plate).
Two is enough to do half a boat bottom (good for a couple coats). I buy three using
two on the bottom and keep one for...
Type: Posts; User: Squirtcha?
I get mine at Grainger. I believe I paid $7.00 per spray can (slip plate).
Two is enough to do half a boat bottom (good for a couple coats). I buy three using
two on the bottom and keep one for...
You're in need of another bump.
Is this Steve's old boat (from Phoenix)? It looks like it. Trying to figure out the rigging by Dan Nelson and the boat residing in Atlanta.
Very nice ride. I just...
I know you're looking to spend $8k but for a river racer turn key, that's low ... really low.
I think you could get a clean CP for that less motor ... this one's pretty nice:...
[B]you guys are making me feel bad now i have my boat on craigslist in phx. i was looking to see if my boat was on ther being crucified lol it has not hit the 120 mph mark yet so theres still hope...
the sad part is ... there has been some money spent there ... alum heads, gauges, paint, interior, etc ...
sad, real sad ...
I'd like to have that Autometer gps speedometer and antennae. That's...
Judging by this photo it looks like it was probably an outboard. No hole cut in the transom for a jetdrive or outdrive (unless patched over) and no log shaft pass through in the bottom. Looks like it...
Yep Joey's right as rain. It was a small block I/O setup. Really weird deal where the trim
was controlled by the entire motor and drive moving/pivoting as one unit. Had a huge
rubber boot on the...
Looks good. Does it run? If it does I'd think do the compression test (or better yet a leak down). If you do the compression test, it might give you some kind of hint as to the compression ratio and...
Glad to hear someone is having good luck with the mallory unilite,I burned up 2 modules,swapped over to msd and never had an issue again.I got a 466 in my boat and my son and i put it together 2 yrs...
Just one more ?. How many motors before Dan Nelson?
Jim
The original (bone stock and possibly the original).
One rebuild by Standard Machine that didn't make it past cam break in.
The one that...
No box Jim. Just a Mallory Unilite distributor and Mallory Promaster coil.
http://www.malloryperformance.com/e-images04-350//5072101.jpg...
Dan thats killer news. Im getting ready to go NOS so your results are encouraging.
About the MSD though, those things rarely fail. And when they do its more than likely installer error(bad ground)...
squirt, look on ebay for a good used 3stage msd retard box if you already have a msd box. i picked up and nearly new 1 last wk for 44bucks to my door, looks brand new.then you can retard for the...
All that tells you is; you aren't running a big enough nitrous jet;) :)
You must be looking for thing's to do or are just curious. After that leak down I' call it quits. Could you here if it was...
Fords suck? (http://www.***boat.com/forums/showthread.php?t=171691) I'm thinking ...........NOT!
After pounding on my motor relentlessly for 6 straight years and running countless bottles of nitrous through it, I figured I'd run a leakdown test on it today. All cylinders read between 4% - 6%...
Yeah, he mentioned having lots of firewood for the cool weather.........didn't say how he was going to keep dry. Rained all day yesterday and promises to do the same today. It's reminiscent of our...
Which one wire alt are you going to use? Motorola marine or a GM internal regulator type? Either one requires a "tickle" wire to the feild to create charge. This wire on both systems usually comes...
I think it'll sink.:D
Just wondering, what do you Arizona boy's consider cold at night in regards to camping?
The lows will be in the mid to upper 40's that week. Highs in the mid to upper 60's
Before ya get any...
That was a real short life as a boat mfr.
Maybe that's the only one of it's kind?:D
Bring your goggles, mittens, mukluks and parkas. It's been real nice during the day, but damned chilly at night and in the mornings. It'll be nice n cool on the water.
That sucker would be made to order for me eh Jim? I could just
swap everything over from the Cheena. The seats in my boat are
shot anyway so I was gonna have to replace em anyway.
They are press in pins. You'd end up with about 500 cu in. Not sure what your question
is regarding the crank and rods though. Will it fit? Yeah. Guess it doesn't really matter
since you don't...
Sorry I screwed up in the above post I put down D1VE
which are block numbers not heads. I meant D3 A2A cylinder
heads. I think you'll find that they're actually 97 cc chambers
on those heads. ...