Reply With QuoteTtt
SOLD
Will part out.Prices added
1) 2 turbonetics 60-1 turbos,water jacketed,seals added for draw-through set-up. They have about 30 hours on them since rebuild.
A/R is 1.30 .Will make 550 hp a piece.I made 24#’s of boost with them and had room for more. $1100.00
2) 2 turbonetics deltagate wastegates with 5 and 9 # springs.Had them rigged so I could change boost levels with a valve on the dash. $175.00 each
3) 1pr Gale Banks aluminum water cooled exhaust for a BBC. $350.00 both
4) 1 PFM intercooler with 2 cores,1 for each turbo with -12 fittings.This bolts to a Edelbrock Street Ram(not included).I bought this from Carson brummet. $450.00
5) 2 3” weber throttle bodies that are bolted to the intercooler.I’ll include the Lokar cable and brackets that control the butterflies. $100.00 each
6: 2 4” chrome plated exhaust pipes with o2 bungs in them.goes with turbos goes with turbos
7: 2 pieces of aluminum piping and silicone fittings to go from compressor to the throttle bodies.
2 bases for the carbs to transition to the turbo compressors.
9: 2 Holley 750 double pumpers that were prepped by Gary Williams for this turbo set-up.These are for a draw through set-up.I haven't used them because i went with EFI.
If you want to go with EFI i’ll sell the carbs with or without the turbos.The carbs will work on a blower deal so either way would be ok with me.I could sell the carbs to someone already but want to wait until the turbos sell.
This set-up would work good on a 454.
$1950.00 for everything but the carbs.
$850.00 for carbs.
Will make a deal for all of it.
I paid ALOT more for everything.
Those turbos sell for $1600.00 each new.
Cell phone # is 979-244-7070
If i don't answer leave a message and i'll call you back when i get a chance.
http://www.***boat.com/image_center/...urboparts1.jpg
http://www.***boat.com/image_center/...turboparts.jpg
Ttt
Are the turbos only water cooled bearing cases or exhaust turbine housings as well? Looks like only bearings? nice set up
Do you have any pics of it all assembled? Im curious if it would fit under my engine hatch? What did it come off of?
not sure you would want to put any of that under the hatch without some mods...unless you like fires. Water jaketed turbines and new exhaust tips would be a must. It could be done with this set up for alot less than a new one though. serious power!
http://www.***boat.com/image_center/...boengine.jpgDo you have any pics of it all assembled? Im curious if it would fit under my engine hatch? What did it come off of?
Would not fit under hood without some changes.
Set-up was on a TX-20.With a 468 BBC it ran 105 mph.
Here is pics in boat.
http://www.***boat.com/image_center/...rboengine1.jpg
What else might I need, to bolt this on my engine and go?
If you want to go with the carbs all you'll need is a Edelbrock street ram intake and some hoses.
If you want to go EFI,of course you'll need the EFI and a SR intake.
This is a good system to get started with.
It ran good for me.
With the water cooled exhaust and turbo housing the system
ran surpisingly cool.You didn't feel the heat on the back of your head.
The turbos spool fast also.I had the EFI tuned so it had hardly no
lag off idle and 0 lag from 1500 and up rpm's.These turbos are
not cheap.
They have water cooled bearing housings and oil lubed bearings.
Interested in seperating at all?? I would only need the turbos, all exhaust and the wastegates with the dumps.
Will you include your EFI setup and hoses so it is a complete bolt on package? If so, would it cost?
Posting Permissions