KORE performance

[Eliminator 4 Life]

I just wanted to know if anyone has ever used or installed any of there products of if anyone is a dealer for them. Thanks Rob

[onesloryd]

I would go with: http://lorenzindustries.com/

[soupersonic]

The consensus over on the TDR is that Kore is the way to go.Out of all the people that have it i have only seen one bad review.Its pricey stuff tho

[Eliminator 4 Life]

Thanks guys any of you ever used any of these products??
Your right supsersonic so are Eliminators but if you want the best cost is not an issue I want reliable :)

[onesloryd]

Which kit are you looking at?

[Eliminator 4 Life]

Which kit are you looking at?
I dont know yet and I really wanna get one that best fits my need and they are concrete cadillac :cool:

[onesloryd]

The way my truck is setup I have about 12” of travel in the front and rear. With the Dodge I all boils down to geometry, I you are not going with the Ultimate or Technical kit if would look at Lorenz or Thuren Fab for your setup. I you want more info. on this just PM me I have done a lot of research and work on this.

[Eliminator 4 Life]

The way my truck is setup I have about 12” of travel in the front and rear. With the Dodge I all boils down to geometry, I you are not going with the Ultimate or Technical kit if would look at Lorenz or Thuren Fab for your setup. I you want more info. on this just PM me I have done a lot of research and work on this.
Well onesloryd i got a 06 mega cab 2500 with the cummins. I drive it to work 5 miles and I tow the boat to lake havasu which is 500 miles from my house my work is 10. I wanna run some 20x10 on the truck but then again Im thinking about ball joint problems since dodges are known for it.I want something that looks off the hook and rides caddy.

[onesloryd]

Well first off you are most likely going to have a problem with the 20 x 10 depending on what size tire you want to run. As for making it ride like a caddy that can be done. How much lift are you looking for? My truck is about 5.5” lift and the tire are 35’s on 17” rims.

[Eliminator 4 Life]

I was thinking 6 or somewhere like what you got. My buddy said this one rides the best KELDERMANMFG.COM

[Eliminator 4 Life]

Well first off you are most likely going to have a problem with the 20 x 10 depending on what size tire you want to run. As for making it ride like a caddy that can be done. How much lift are you looking for? My truck is about 5.5” lift and the tire are 35’s on 17” rims.
I will probably run a toyo open country I dont like noisey aggresive tires :crossx:

[onesloryd]

Kelderman is a nice setup plus it is somewhat adjustable for height. I am currently running Toyo Open Country A/T’s and they are real quiet.

[Eliminator 4 Life]

This thing is crazy

[onesloryd]

Just remember anything over 6” is going to need cut and pivot drive shaft etc. The alignment on a Dodge is real critical.
http://valleyspringservice.com/project2_dodge8inch_page.htm

[soupersonic]

Heres a 6" lift for ya
Kore (http://turbodieselregister.com/forums/showthread.php?t=157885)

[Eliminator 4 Life]

Heres a 6" lift for ya
Kore (http://turbodieselregister.com/forums/showthread.php?t=157885)
So i dont get what u are saying :)

[Eliminator 4 Life]

Just remember anything over 6” is going to need cut and pivot drive shaft etc. The alignment on a Dodge is real critical.
http://valleyspringservice.com/project2_dodge8inch_page.htm
I want 6 or less :cool:

[onesloryd]

Have you looked at the Fabtech kit?
If I am not mistaken the KORE Technical 6” kit is about 10K not installed and in my opinion it is missing a couple of items.

[Eliminator 4 Life]

Have you looked at the Fabtech kit?
If I am not mistaken the KORE Technical 6” kit is about 10K not installed and in my opinion it is missing a couple of items.
I agree the kore is pricey but do you really think the fab tech kit is that good. I think the kedlerman might be the way to go but I still dont know.

[onesloryd]

I personally don’t know how good the Fabtech kit is, but I am sure it is better than the Superlift kit. Kelderman is nice, I had looked at it before did my setup, but remember it converts the rear to a four link and the kit also requires you to use an indexing ring on the transfer case, which in turn requires major trimming/cutting of the cross member. Have you determined what tire dia. you would like to run?
Check out Lorenz site in the buildup section there is a black mega cab with 20’s.

[Eliminator 4 Life]

I personally don’t know how good the Fabtech kit is, but I am sure it is better than the Superlift kit. Kelderman is nice, I had looked at it before did my setup, but remember it converts the rear to a four link and the kit also requires you to use an indexing ring on the transfer case, which in turn requires major trimming/cutting of the cross member. Have you determined what tire dia. you would like to run?
Check out Lorenz site in the buildup section there is a black mega cab with 20’s.
I cant find the black mega cab or the pics for that matter.

[onesloryd]

http://lorenzindustries.com/buildup_mike.shtml

[UnionJack]

I just had jason at rancho motor sports put a superlift kit on my new mega cab cummins, and its great

[onesloryd]

I wasn’t saying that Superlift is bad, I have heard a fair amount of people have had problems with death wobble & shocks.

[Eliminator 4 Life]

I just had jason at rancho motor sports put a superlift kit on my new mega cab cummins, and its great
UJ lets see some pics of it and I hope you didnt get the color I got :p