Need a 1 13/16 deep socket

[BrendellaJet]

Where to get in OC? I tried Mcfadden Dale, no dice. Needs to be fit over a 3 inch shaft.

[Cigalert]

www.mcmaster.com
they deliver next day or you can cruise up to their place in buena park...I think.

[robk]

Impeller nut?
Last time I needed one that size, I had to cut a short socket across the middle and welded in an extension... couldn't find a deep one that day, and it held up under the impact wrench.
Rob

[shippingguy]

Try Lowes or Home Depot. I have seen them there in the past.

[BrendellaJet]

Impeller nut. Need to take the suction housing to powder coat. I might just go up to rex and grab one.

[BrendellaJet]

Try Lowes or Home Depot. I have seen them there in the past.
they dont cary anything within a half inch of this size.

[randomhero]

if you dont find the tool your looking for i can make one very easy and cheap,i have a fab shop just for this sort of thing. pm me and i will send my contact

[Squirtin Thunder]

Just shoot down to Rex Marine and pic up an impeller nut socket !

[Baja Big Dog]

The tool guy across the street from Mc Fadden dale, towards Kramer (the anaheim store).
Impact?

[BrendellaJet]

The tool guy across the street from Mc Fadden dale, towards Kramer (the anaheim store).
Impact?
Jim I dont want to go to Rex. Boat is with me so It would take me an hour and a half...
Big Dog, do you have a # by any chance?

[Squirtin Thunder]

I have one you can use I also have a combination wrench that size.

[BrendellaJet]

Thanks for the offer. I can see myself needing this more than once though so Im just gonna buy one.

[robk]

Jim I dont want to go to Rex. Boat is with me so It would take me an hour and a half...
Big Dog, do you have a # by any chance?
Well if all else fails you can borrow mine, but its in Brea.
Rob

[Baja Big Dog]

Jim I dont want to go to Rex. Boat is with me so It would take me an hour and a half...
Big Dog, do you have a # by any chance?
Gotta go look at a job. search under tools Anaheim, hes on La Palma, I think there is a couple of tool guys there. Between Kramer and RedGum...

[502 JET]

Do you have a Sears out there?
I doubt you will find a socket off the shelf thats deep enough. I cut mine and welded in a piece of pipe as suggested above.
Cut the nut off and order a new nut save your self all the running around.

[BrendellaJet]

Do you have a Sears out there?
I doubt you will find a socket off the shelf thats deep enough. I cut mine and welded in a piece of pipe as suggested above.
Cut the nut off and order a new nut save your self all the running around.
That would work except Id still need to get the socket so I could torque the new one on.

[HOOTER SLED-]

Harbor Freight?????????

[yopengo]

I just checked and the largest deep I have is 1 1/8". I could have driven it over....:(
Try to PM Goad in Foothill. He is a Jet freak like me.

[Froggystyle]

Go to MPD in Costa Mesa with the boat ready to pull and have him pull your nut for you today. Then, order the new socket from Rex for tomorrow and when you are ready to install, you will have your socket already.
I do know one person with one in Anaheim, but he wouldn't lend it out I don't think.

[Dan Lorenze]

I drove around looking for a socket for half the day, no luck.... I ended up going to MPD and let them do it. Rex has the tool...