Way to go Shaun ! Tom
Type: Posts; User: jetboatperformance
Way to go Shaun ! Tom
I have the insert in stock (cheap) and the hand hole cleanouts (used) are plentiful call or pm if I can help you Tom www.jetboatperformance.com
RC call if we can help , weve built several SBC and SBF boats over the years , my 16' ran 80, Love these little motors make good inexpensive HP Tom ...
Covered. How much of a perfomance gain could I expect? Is it worth the cost?
Thanks again
Depending on what you have already, with Improved Intake and Carb (vs stock) you can look for 10 to 15%...
Taking it off and /will require alot of work to fill and "french" as well as leave you unprotected from "dock kisses etc , We sell the moldings and filler strips(lots of differerent sizes) call if we...
I'm trying to keep them original looking, mostly need the face replaced as most are faded because of stored outside & the sun deteriorated the plastic face, also some have the needle or needles...
Nick ,Welcome to the boards and the world of Jet Boats , Great story ! good read ! Good luck with the boat lets us know if we can help Tom
Sterling If this is what you decide , dry headers IMO are definatley out due both extreme heat and to potential fire hazard possibilities, Water injected such as Bassett or Rewarder would be an...
Nice Boat JS ,I'm digging thru my "archive" to find some info for you We've worked on several nice Witchcrafts over the years! Welcome to the boards Enjoy your boat ! Tom
Marlin your boat was /is a very popular boat typical of the 70's. I couldn't immediatley find any info on Them but we have worked on several over the years and they to me ressemble the Tahitis and...
If you sent them to the yahoo acct. then I didn't get them. If you sent them to my other e-mail I'll have to check monday. Re the crank it could only happen to me.lol I'd still like to know what is...
Kreg Thats amazing , thought I'd seen evrything ! did ya get the header pics ??
It's a long shot but you may want to have someeone turn the motor over while you look at the impeller to make sure it's turning, I had a crank bust right in the center of the rear main and it still...
CP the guys pretty much called it here The high rpms vs speed suggests a "disconnect" between motor and jet or for example ,debris (rock ,stick,panties,cat fish etc) in the jet impleller or simply a...
That's a beauty.
Terrible time to be trying to get money back out of a boat though.
http://i16.ebayimg.com/06/i/001/16/b2/c575_12.JPG
Be that as it may this IS a no BS,no"Ebay speed" fast A$$...
John we've been using Cometics for years after encountering problems with dead softs and orings , My Buddy Hals BGF motor and Joshs both have them and Hals has 4 seasons ,They're laminate type...
Thru fairly exaustive research I've found that its seems "catch as catch can" is the deal . Stories and posts seem to be arbitrary in results , some agents will write stuff that others won't etc. ...
Nubbs check PMs for cell# Tom
Nubbs I have (& sell ) similar risers/tailpipes as you describe ,depending on cam choice they could be critical in fact let me know if we can help you on this Tom
(this is a V-drive application...
Your New Bowl is a late AT bolt pattern set up for an O'ring seal vs the older paper gasket, for you to use it with your older suction it will require machining, redrilling and some minor work to...
I understand that Berklery made a lil 1/2 pint pump at one time. Think it was a 6JACW with a max horse power of 45. Can you tell me when were they made and what the heck were the used in?
Thanks! ...
Ryan don't know who this Earl character is but he's clearly incorrect :( When my son was still in grade school (hes now my chief engineer and VP ) I "horse traded"(for a small block chevy) the...
Mid, Josh (@12yrs) and I built that litttle boat years ago with a 550 Kawi Jet ski motor and jet and a "One off hull" that i think was built by Miller in Santa Maria We sold it no less than 5 or 6...
Rich AT and Dominator Bowls and Impellers (in the original form) are set up with a rear wear skirt which fits into the machined area at the rear of the bowl , This negates the need for an add on ...
Reverse shift pattern, manual V/B ,no torque converter , Hughes Trans in AZ has done all mine very good folks Tom
http://i147.photobucket.com/albums/r319/jetboatperformance/69%20Schiada/DSC00459.jpg